| Properties Summary |
| Defined in: nd:AIfPol |
nd:IfControl
scalar:Bitmask16
|
ctrl (nd:AIfPol:ctrl)
The control state.
|
nd:HopLimit
scalar:UByte
|
hopLimit (nd:AIfPol:hopLimit)
The hop limit is used by hosts in outgoing packets and link parameters such as the link MTU. This facilitates centralized administration of critical parameters that can be set on routers and automatically propagated to all attached hosts.
|
nd:Mtu
scalar:Uint16
|
mtu (nd:AIfPol:mtu)
In the RA message, the maximum transmission unit (MTU) value that a host should use in packets that it originates.
|
nd:NsIntvl
scalar:Uint32
|
nsIntvl (nd:AIfPol:nsIntvl)
The neighbor solicitation interval is sent by a node to determine the link-layer address of a neighbor, or to verify that a neighbor is still reachable through a cached link-layer address. Neighbor solicitations are also used for duplicate address detection.
|
nd:NsRetries
scalar:UByte
|
nsRetries (nd:AIfPol:nsRetries)
The retransmission retry count for for sending neighbor solicitation messages.
|
nd:RaIntvl
scalar:Uint16
|
raIntvl (nd:AIfPol:raIntvl)
The interval for sending router advertisement messages.
|
nd:RaLifetime
scalar:Uint16
|
raLifetime (nd:AIfPol:raLifetime)
The lifetime associated with the default router.
|
nd:ReachableTime
scalar:Uint32
|
reachableTime (nd:AIfPol:reachableTime)
The reachable time, which is the time in milliseconds that a node assumes a neighbor is reachable after receiving a reachability confirmation.
|
nd:RetransTimer
scalar:Uint32
|
retransTimer (nd:AIfPol:retransTimer)
The retransmit timer has the time in milliseconds between retransmitted neighbor solicitation messages.
|
childAction
Type: mo:ModificationChildAction
Primitive Type: scalar:Bitmask32
Units: null
Encrypted: false
Access: implicit
Category: TopLevelChildAction
Comments:
-
Delete or ignore. For internal use only.
| |
| Constants |
| deleteAll |
16384u |
deleteAll |
NO COMMENTS
|
| ignore |
4096u |
ignore |
NO COMMENTS
|
| deleteNonPresent |
8192u |
deleteNonPresent |
NO COMMENTS
|
| DEFAULT |
0 |
--- |
This type is used to
|
|
ctrl
Type: nd:IfControl
Primitive Type: scalar:Bitmask16
Like: nd:If:ctrl
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Comments:
-
The control state.
| |
| Constants |
| unspecified |
0 |
Unspecified |
Unspecified
|
| managed-cfg |
2 |
Managed config |
redirects
Not Supported
Managed config, this flag is advertised in ICMPv6 RA
messages to use stateful address auto-configuration
to obtain address information
|
| other-cfg |
4 |
Other config |
Other config, this flag is advertised in ICMPv6 RA
messages that hosts use stateful auto configuration
to obtain non address related information
|
| suppress-ra |
8 |
Suppress RA |
suppress-ra
|
| suppress-ra-mtu |
16 |
Suppress RA mtu |
suppress-ra mtu
|
| unsolicit-na-glean |
32 |
Unsolicit NA Glean |
unsolicit-na-glean, enable neighbor gleaning on receipt of unsolicit NA
|
| DEFAULT |
unspecified(0) |
Unspecified |
Unspecified
|
|
descr
Type: naming:Descr
Primitive Type: string:Basic
Like: naming:Described:descr
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: "0" max: "128"
Allowed Chars:
Regex: [a-zA-Z0-9\\!#$%()*,-./:;@ _{|}~?&+]+
Comments:
-
Specifies a description of the policy definition.
dn
Type: reference:BinRef
Units: null
Encrypted: false
Access: implicit
Category: TopLevelDn
Comments:
-
A tag or metadata is a non-hierarchical keyword or term assigned to the fabric module.
hopLimit
Type: nd:HopLimit
Primitive Type: scalar:UByte
Like: nd:If:hopLimit
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: (short)0 max: (short)255
Comments:
-
The hop limit is used by hosts in outgoing packets and link parameters such as the link MTU. This facilitates centralized administration of critical parameters that can be set on routers and automatically propagated to all attached hosts.
| |
| Constants |
| defaultValue |
64 |
--- |
NO COMMENTS
|
|
mtu
Type: nd:Mtu
Primitive Type: scalar:Uint16
Like: nd:If:mtu
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: 1280 max: 9000
Comments:
-
In the RA message, the maximum transmission unit (MTU) value that a host should use in packets that it originates.
| |
| Constants |
| defaultValue |
9000 |
--- |
NO COMMENTS
|
|
name
Type: naming:Name
Primitive Type: string:Basic
Overrides:naming:NamedObject:name
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: "0" max: "64"
Allowed Chars:
Regex: [a-zA-Z0-9_.:-]+
Comments:
-
null
nameAlias
Type: naming:NameAlias
Primitive Type: string:Basic
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: "0" max: "63"
Allowed Chars:
Regex: [a-zA-Z0-9_.-]+
Comments:
-
NO COMMENTS
nsIntvl
Type: nd:NsIntvl
Primitive Type: scalar:Uint32
Like: nd:If:nsIntvl
Units: msec
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: (long)1000l max: (long)3600000l
Comments:
-
The neighbor solicitation interval is sent by a node to determine the link-layer address of a neighbor, or to verify that a neighbor is still reachable through a cached link-layer address. Neighbor solicitations are also used for duplicate address detection.
| |
| Constants |
| defaultValue |
1000u |
--- |
NO COMMENTS
|
|
nsRetries
Type: nd:NsRetries
Primitive Type: scalar:UByte
Like: nd:If:nsRetries
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: (short)1 max: (short)100
Comments:
-
The retransmission retry count for for sending neighbor solicitation messages.
| |
| Constants |
| defaultValue |
3 |
--- |
NO COMMENTS
|
|
ownerKey
Type: naming:Descr
Primitive Type: string:Basic
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: "0" max: "128"
Allowed Chars:
Regex: [a-zA-Z0-9\\!#$%()*,-./:;@ _{|}~?&+]+
Comments:
-
The key for enabling clients to own their data for entity correlation.
ownerTag
Type: naming:Descr
Primitive Type: string:Basic
Units: null
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: "0" max: "64"
Allowed Chars:
Regex: [a-zA-Z0-9\\!#$%()*,-./:;@ _{|}~?&+]+
Comments:
-
A tag for enabling clients to add their own data. For example, to indicate who created this object.
raIntvl
Type: nd:RaIntvl
Primitive Type: scalar:Uint16
Like: nd:If:raIntvl
Units: sec
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: 200 max: 1800
Comments:
-
The interval for sending router advertisement messages.
| |
| Constants |
| defaultValue |
600 |
--- |
NO COMMENTS
|
|
raLifetime
Type: nd:RaLifetime
Primitive Type: scalar:Uint16
Like: nd:If:raLifetime
Units: sec
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: 0 max: 9000
Comments:
-
The lifetime associated with the default router.
| |
| Constants |
| defaultValue |
1800 |
--- |
NO COMMENTS
|
|
reachableTime
Type: nd:ReachableTime
Primitive Type: scalar:Uint32
Like: nd:If:reachableTime
Units: msec
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: (long)0l max: (long)3600000l
Comments:
-
The reachable time, which is the time in milliseconds that a node assumes a neighbor is reachable after receiving a reachability confirmation.
| |
| Constants |
| defaultValue |
0u |
--- |
NO COMMENTS
|
|
retransTimer
Type: nd:RetransTimer
Primitive Type: scalar:Uint32
Like: nd:If:retransTimer
Units: msec
Encrypted: false
Access: admin
Category: TopLevelRegular
Property Validators:
Range: min: (long)0l max: (long)0xffffffffl
Comments:
-
The retransmit timer has the time in milliseconds between retransmitted neighbor solicitation messages.
| |
| Constants |
| defaultValue |
0u |
--- |
NO COMMENTS
|
|
rn
Type: reference:BinRN
Units: null
Encrypted: false
Access: implicit
Category: TopLevelRn
Comments:
-
Identifies an object from its siblings within the context of its parent object. The distinguished name contains a sequence of relative names.
status
Type: mo:ModificationStatus
Primitive Type: scalar:Bitmask32
Units: null
Encrypted: false
Access: implicit
Category: TopLevelStatus
Comments:
-
The upgrade status. This property is for internal use only.
| |
| Constants |
| created |
2u |
created |
In a setter method: specifies that an object should be created.
An error is returned if the object already exists.
In the return value of a setter method: indicates that an object has been created.
|
| modified |
4u |
modified |
In a setter method: specifies that an object should be modified
In the return value of a setter method: indicates that an object has been modified.
|
| deleted |
8u |
deleted |
In a setter method: specifies that an object should be deleted.
In the return value of a setter method: indicates that an object has been deleted.
|
| DEFAULT |
0 |
--- |
This type controls the life cycle of objects passed in the XML API.
When used in a setter method (such as configConfMo), the ModificationStatus
specifies whether an object should be created, modified, deleted or removed.
In the return value of a setter method, the ModificationStatus indicates the actual
operation that was performed. For example, the ModificationStatus is set to "created"
if the object was created. The ModificationStatus is not set if the object was neither
created, modified, deleted or removed.
When invoking a setter method, the ModificationStatus is optional:
If a setter method such as configConfMo is invoked and the ModificationStatus
is not set, the system automatically determines if the object should be created or modified.
|
|
![[V]](styles/eye.gif)