vpc:Keepalive
The vPC keepalive definitions.
Telemetry Sensor Path(s)
Configurable Properties
| PROPERTY NAME | DATA TYPE | DESCRIPTION | PERMITTED VALUES |
|---|---|---|---|
| destIp | address:Ip |
destination address | Value must match ipv4 or ipv6 known format |
| flushTout | vpc:FlushTout (scalar:Uint32) |
flush timeout | RANGE: [3 , 10] DEFAULT: 3 |
| interval | vpc:KeepaliveInterval (scalar:Uint32) |
interval | RANGE: [400 , 10000] DEFAULT: 1000 |
| name | naming:Name (string:Basic) |
Name | MAX SIZE: 16 |
| precType | vpc:PrecType (scalar:Enum8) |
precedence type | SELECTION: 0 - network 1 - internet 2 - critical 3 - flash-override 4 - flash 5 - immediate 6 - priority 7 - routine DEFAULT: routine |
| precValue | vpc:PrecValue (scalar:UByte) |
precedence value | RANGE: [0 , 7] DEFAULT: 6 |
| srcIp | address:Ip |
source address | Value must match ipv4 or ipv6 known format |
| timeout | vpc:KeepaliveTout (scalar:Uint32) |
timeout | RANGE: [3 , 20] DEFAULT: 5 |
| tosByte | vpc:TosByte (scalar:UByte) |
tos byte | RANGE: [0 , 255] DEFAULT: 0 |
| tosCfgType | vpc:TosCfgType (scalar:Enum8) |
tos config type | SELECTION: 0 - noCfg 1 - tos-byte 2 - tos-value 3 - tos-type 4 - precedence-type 5 - precedence-value DEFAULT: noCfg |
| tosType | vpc:TosType (scalar:Enum8) |
tos type | SELECTION: 0 - min-delay 1 - max-throughput 2 - max-reliability 3 - min-monetary-cost 4 - normal DEFAULT: normal |
| tosValue | vpc:TosValue (scalar:UByte) |
tos value | RANGE: [0 , 15] DEFAULT: 0 |
| udpPort | comm:Port (scalar:Uint32) |
port number | RANGE: [1 , 65535] |
| vrf | l3:VrfName (string:Basic) |
vrf name | A sequence of characters |
Operational Properties
| PROPERTY NAME | DATA TYPE | DESCRIPTION | POSSIBLE VALUES |
|---|---|---|---|
| operSt | vpc:KeepaliveOperSt (scalar:Bitmask8) |
operational state | SELECTION: 0 - not-applicable 1 - suspended 2 - vrf-invalid 4 - domain-mismatch 8 - operational 16 - send-failed 32 - recv-failed 64 - peer-was-alive DEFAULT: 0 |
| peerUpTime | string:Basic |
Duration for which peer is alive for | A sequence of characters |
| recvIf | nw:IfId (base:IfIndex) |
recv interface | Must match first field in the output of show intf brief. Example: Eth1/1 or Vlan100 |
| sendIf | nw:IfId (base:IfIndex) |
send interface | Must match first field in the output of show intf brief. Example: Eth1/1 or Vlan100 |
Internal Properties
| PROPERTY NAME | DATA TYPE | DESCRIPTION | POSSIBLE VALUES |
|---|---|---|---|
| modTs | mo:TStamp (scalar:Date) |
The time when this object was last modified. | SELECTION: 0 - never DEFAULT: never |
| status | mo:ModificationStatus (scalar:Bitmask32) |
The upgrade status. This property is for internal use only. | SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced |