l1:PhysIf

The object that represents the Layer 1 physical Ethernet interface information object.

Telemetry Sensor Path(s)
Configurable Properties
PROPERTY NAME DATA TYPE DESCRIPTION PERMITTED VALUES
FECMode l1:FECMode
(scalar:Enum8)		 FEC Mode SELECTION:
1 - fc-fec
2 - rs-fec
3 - fec-off
4 - auto
5 - rs-ieee
6 - rs-cons16
7 - kp-fec
DEFAULT: auto
accessVlan l1:l1IfAccessVlan
(base:Encap)		 Configured Access Vlan SELECTION: unknown, vlan-%d or vxlan-%d
DEFAULT: vlan-1
adminSt l1:AdminSt
(scalar:Enum8)		 Administrative port state SELECTION:
1 - down
2 - up
DEFAULT: up
autoNeg l1:AutoNeg
(scalar:Enum8)		 Administrative port auto-negotiation SELECTION:
1 - on
2 - off
3 - 25G
DEFAULT: on
beacon l1:Beacon
(scalar:Enum8)		 Beacon State SELECTION:
1 - on
2 - off
DEFAULT: off
bw l1:Bw
(scalar:Uint32)		 The bandwidth parameter for a routed interface, port channel, or subinterface.
RANGE: [0 , 3200000000]
DEFAULT: 0
controllerId aggregate:ControllerIdBitmap
(base:BitArray)		 Controller ID
ARRAY SIZE: 256
delay l1:Delay
(scalar:Uint32)		 The administrative port delay time.
RANGE: [1 , 16777215]
DEFAULT: 1
descr naming:Descr1024
(string:Basic)		 descr
MAX SIZE: 254
dfeAdaptiveTuning l1:DfeAdaptiveTuning
(scalar:Enum8)		 DFE (Decision Feedback Equalizer) Adaptive Tuning SELECTION:
0 - disable
1 - enable
DEFAULT: enable
dfeTuningDelay l1:DfeTuningDelay
(scalar:Uint16)		 DFE (Decision Feedback Equalizer) Tuning Delay
RANGE: [100 , 10000]
DEFAULT: 100
dot1qEtherType l1:DDot1qEtherType
(scalar:Uint32)		 The administrative port Dot1q ether-type. Dot1q Ether Type configures the TPID value in the VLAN tag field for packets received and sent by the interface.
RANGE: [1536 , 65535]
DEFAULT: 0x8100
duplex l1:Duplex
(scalar:Enum8)		 Duplex SELECTION:
1 - auto
2 - full
3 - half
DEFAULT: auto
inhBw l1:InheritBw
(scalar:Uint32)		 Administrative port inherit bandwidth
RANGE: [0 , 4294967295]
DEFAULT: 4294967295
ituChannel l1:ItuChannel
(scalar:Uint32)		 ITU Channel to support DWDM XCVR
RANGE: [1 , 96]
DEFAULT: 32
layer l1:Layer
(scalar:Enum8)		 Administrative port layer SELECTION:
0 - Layer1
1 - Layer2
2 - Layer3
DEFAULT: Layer2
linkActiveJitterMgmt l1:LinkActiveJitterMgmt
(scalar:Enum8)		 Administrative port link active-jitter-management SELECTION:
0 - disable
1 - enable
DEFAULT: disable
linkDebounce l1:LinkDebounce
(scalar:Uint16)		 Administrative port link debounce interval
RANGE: [0 , 20000]
DEFAULT: 100
linkDebounceLinkUp l1:LinkDebounceLinkUp
(scalar:Uint16)		 Link Debounce Interval - LinkUp Event
RANGE: [0 , 10000]
DEFAULT: 0
linkFlapErrDis l1:LinkFlapErrDis
(scalar:Enum8)		 Enable/Disable Link Flap Error Config SELECTION:
0 - disable
1 - enable
DEFAULT: disable
linkFlapErrorMax l1:MaxFlaps
(scalar:Uint16)		 Max Flaps allowed per time
RANGE: [2 , 30]
DEFAULT: 30
linkFlapErrorSeconds l1:FlapSeconds
(scalar:Uint16)		 Time Allowed for max flaps
RANGE: [5 , 420]
DEFAULT: 420
linkLog l1:LinkLog
(scalar:Enum8)		 Administrative link logging enable SELECTION:
1 - default
2 - enable
3 - disable
DEFAULT: default
linkLoopback l1:LinkLoopback
(scalar:Enum8)		 Link loopback configuration SELECTION:
0 - disable
1 - enable
DEFAULT: disable
linkMacUpTimer l1:LinkMacUpTimer
(scalar:Uint16)		 Administrative port link mac-up timer
RANGE: [0 , 120]
DEFAULT: 0
linkMaxBringUpTimer l1:LinkMacUpTimer
(scalar:Uint16)		 Administrative port link mac-up timer max
RANGE: [0 , 120]
DEFAULT: 0
linkTransmitReset l1:LinkTransmitReset
(scalar:Enum8)		 Link Transmit Reset SELECTION:
0 - disable
1 - enable
DEFAULT: enable
mdix l1:Mdix
(scalar:Enum8)		 The administrative Mdix mode. The Medium-dependant interface crossover (Mdix) is when the interface automatically detects the required cable connection type (straight through or crossover) and configures the connection appropriately. SELECTION:
1 - auto
2 - mdi
3 - mdi-x
DEFAULT: auto
mediaType l1:MediaType
(scalar:Enum8)		 phy interfaces media type SELECTION:
0 - none
1 - 10g-tx
DEFAULT: none
medium l1:Medium
(scalar:Enum8)		 The administrative port medium type. SELECTION:
1 - broadcast
2 - p2p
DEFAULT: broadcast
mode l1:Mode
(scalar:Enum8)		 Administrative port mode SELECTION:
1 - access
2 - trunk
3 - fex-fabric
4 - dot1q-tunnel
5 - promiscuous
6 - host
7 - trunk_secondary
8 - trunk_promiscuous
9 - vntag
DEFAULT: access
mtu l1:Mtu
(scalar:Uint32)		 Administrative port mtu
RANGE: [576 , 9216]
DEFAULT: 1500
name naming:Name256
(string:Basic)		 The name of the object.
MAX SIZE: 63
nativeVlan l1:l1IfNativeVlan
(base:Encap)		 Configured Native Vlan SELECTION: unknown, vlan-%d or vxlan-%d
DEFAULT: vlan-1
packetTimestampEgressSourceId l1:PacketTimestampSourceId
(scalar:Uint32)		 Egress timestamp Source Id
RANGE: [0 , 8388606]
DEFAULT: 0
packetTimestampIngressSourceId l1:PacketTimestampSourceId
(scalar:Uint32)		 Ingress timestamp Source Id
RANGE: [0 , 8388606]
DEFAULT: 0
packetTimestampState l1:PacketTimestampState
(scalar:Enum8)		 packet timestamp feature state SELECTION:
0 - disable
1 - enable-ingress
2 - enable-egress
3 - enable-both
DEFAULT: disable
portT eqpt:PortT
(scalar:Enum16)		 Type of the port: Fabric vs Leaf SELECTION:
0 - unknown
1 - eobc
2 - mgmt
3 - fab
4 - leaf
5 - extchhp
6 - extchfp
DEFAULT: unknown
routerMac address:MAC
 The administrative router MAC address. Value must match MM:MM:MM:SS:SS:SS format
DEFAULT: not-applicable
snmpTrapSt l1:SnmpTrapSt
(scalar:Enum8)		 Administrative port snmp trap state SELECTION:
1 - enable
2 - disable
DEFAULT: enable
spanMode l1:SpanMode
(scalar:Enum8)		 Administrative port span mode SELECTION:
1 - not-a-span-dest
2 - span-dest
3 - span-dest-fwd
4 - span-dest-fwd-learn
DEFAULT: not-a-span-dest
speed l1:Speed
(scalar:Enum8)		 Administrative port speed SELECTION:
0 - unknown
2 - 100M
3 - 1G
4 - 10G
5 - 40G
6 - auto
7 - auto 100M
8 - auto 100M 1G
9 - 100G
10 - 25G
11 - 10M
12 - 50G
13 - 200G
14 - 400G
15 - 2.5G
16 - 5G
17 - auto 2.5G 5G 10G
18 - auto 100M 1G 2.5G 5G
19 - 800G
DEFAULT: auto
speedGroup l1:SpeedGroup
(scalar:Enum8)		 Speed Group SELECTION:
0 - unknown
3 - 1000
4 - 10000
5 - 40000
6 - auto
10 - 25000
DEFAULT: auto
transMode l1:TransMode
(scalar:Enum8)		 Administrative port layer1 mode SELECTION:
1 - not-a-trans-port
2 - trans-port
DEFAULT: not-a-trans-port
trunkLog l1:TrunkLog
(scalar:Enum8)		 Administrative trunk logging enable SELECTION:
1 - default
2 - enable
3 - disable
DEFAULT: default
trunkVlans l1:l1IfTrunkVlans
(l2:VlanBitmap)		 Configed Trunk Vlans
DEFAULT: 1-4094
uniDirectionalEthernet l1:UniDirectionalEthernet
(scalar:Enum8)		 UDE (Uni-Directional Ethernet) SELECTION:
0 - disable
1 - send-only
2 - receive-only
DEFAULT: disable
usage l1:PortUsage
(scalar:Bitmask8)		 The port usage type. SELECTION:
1 - discovery
2 - epg
4 - fabric
8 - infra
16 - controller
32 - blacklist
DEFAULT: discovery
userCfgdFlags l1:userCfgdFlags
(scalar:Bitmask8)		 Port User Config Flags SELECTION:
0 - none
1 - admin_state
2 - admin_layer
4 - admin_router_mac
8 - admin_dce_mode
16 - admin_mtu
DEFAULT: none
voicePortCos l1:VoicePortCos
(scalar:SByte)		 Voice Port Cos
RANGE: [-1 , 7]
DEFAULT: none
voicePortTrust l1:VoicePortTrust
(scalar:SByte)		 Voice Port Trust SELECTION:
-1 - disable
8 - enable
DEFAULT: disable
voiceVlanId l1:VoiceVlanId
(scalar:Uint16)		 Voice VLAN ID
RANGE: [0 , 4092]
DEFAULT: none
voiceVlanType l1:VoiceVlanType
(scalar:Enum8)		 Voice vlan type SELECTION:
0 - none
1 - tagged
2 - dot1p
3 - untagged
DEFAULT: none
Operational Properties
PROPERTY NAME DATA TYPE DESCRIPTION POSSIBLE VALUES
operUpdatedOpc scalar:Uint32
 Oper Updated For Opcode RANGE: [0, 4294967295]
Internal Properties
PROPERTY NAME DATA TYPE DESCRIPTION POSSIBLE VALUES
id nw:IfId
(base:IfIndex)		 An identifier . Must match first field in the output of show intf brief. Example: Eth1/1 or Vlan100
modTs mo:TStamp
(scalar:Date)		 The time when this object was last modified. SELECTION:
0 - never
DEFAULT: never
status mo:ModificationStatus
(scalar:Bitmask32)		 The upgrade status. This property is for internal use only. SELECTION:
2 - created
4 - modified
8 - deleted
16 - replaced
switchingSt l1:SwitchingSt
(scalar:Enum8)		 Switching state SELECTION:
0 - disabled
1 - enabled
DEFAULT: disabled