Overview  Diagram  Inheritance  Events  Faults  FSMs  Properties Summary  Properties Detail 

Class ethpm:If (ABSTRACT)

Class ID:3640
Class Label: Interface
Encrypted: false - Exportable: false - Persistent: false - Configurable: false - Subject to Quota: Disabled
Write Access: [NON CONFIGURABLE]
Read Access: [access-connectivity-l1, admin]
Creatable/Deletable: derived (see Container Mos for details)
Possible Semantic Scopes: Infra, Fabric,
Semantic Scope Evaluation Rule: Subclasses
Monitoring Policy Source: Parent
Monitoring Flags : [ IsObservable: true, HasStats: false, HasFaults: true, HasHealth: true, HasEventRules: true ]

Interface information holder.

Naming Rules 


DN FORMAT:


Diagram

Sub Mos: ethpm:AggrIf, ethpm:PhysIf,
Contained Mos: ethpm:PortCap,


Inheritance
[V] ethpm:If Interface information holder.
 ├
 		[V] ethpm:AggrIf Port channel interface information.
 ├
 		[V] ethpm:PhysIf Physical interface information holder


Events 
                ethpm:If:ethpm_If_portup

                ethpm:If:ethpm_If_portInfoDown


Faults 
                ethpm:If:portDownFabric

                ethpm:If:portDownInfraEpg

                ethpm:If:portDownInfraNoEpg

                ethpm:If:portDownNoInfra


Fsms


Properties Summary
Defined in: ethpm:If
base:Encap accessVlan  (ethpm:If:accessVlan)
           The VLAN port access state.
l2:VlanBitmap
          base:BitArray4096 		allowedVlans  (ethpm:If:allowedVlans)
           allowed vlans
address:MAC backplaneMac  (ethpm:If:backplaneMac)
           port backplane mac
scalar:Uint32 bundleBupId  (ethpm:If:bundleBupId)
           bundle bringup id
nw:IfId
          base:IfIndex 		bundleIndex  (ethpm:If:bundleIndex)
           The interface bundle index. A bundle index is a table for a particular output primitive. It defines the workstation dependent aspects of the primitive.
base:Encap cfgAccessVlan  (ethpm:If:cfgAccessVlan)
           The port configuration access VLAN.
base:Encap cfgNativeVlan  (ethpm:If:cfgNativeVlan)
           The port configuration native VLAN.
scalar:Uint32 currErrIndex  (ethpm:If:currErrIndex)
           current error index
l1:DiagsT
          scalar:Enum8 		diags  (ethpm:If:diags)
           port diags type
scalar:Uint32 encap  (ethpm:If:encap)
           port encap
scalar:Bool errDisTimerRunning  (ethpm:If:errDisTimerRunning)
           error disable recovery time running
ethpm:ErrorVlanStatusList
          scalar:Uint32 		errVlanStatusHt  (ethpm:If:errVlanStatusHt)
           port per vlan error state
l2:VlanBitmap
          base:BitArray4096 		errVlans  (ethpm:If:errVlans)
           errored vlans
l2:DomId
          scalar:Uint32 		hwBdId  (ethpm:If:hwBdId)
           hw bd id (allocated for l3 ports, port-channels)
l2:HwRsrcIdT
          scalar:Uint32 		hwResourceId  (ethpm:If:hwResourceId)
           Hardware resource identifier (allocated by eltm)
l1:IntfT
          scalar:Enum8 		intfT  (ethpm:If:intfT)
           interface type
scalar:Uint64 iod  (ethpm:If:iod)
           iod
ethpm:LastErrorsList
          base:Uint32Array4 		lastErrors  (ethpm:If:lastErrors)
           last seen errors
scalar:Date lastLinkStChg  (ethpm:If:lastLinkStChg)
           Last link state change
scalar:Uint32 media  (ethpm:If:media)
           port media
base:Encap nativeVlan  (ethpm:If:nativeVlan)
           port native vlan
scalar:Uint32 numOfSI  (ethpm:If:numOfSI)
           number of sub-interfaces
ethpm:PortOperBitmap
          base:BitArray64 		operBitset  (ethpm:If:operBitset)
           port oper bitset
l1:DceMode
          scalar:Enum8 		operDceMode  (ethpm:If:operDceMode)
           Operational Dce Mode
l1:Duplex
          scalar:Enum8 		operDuplex  (ethpm:If:operDuplex)
           The operational duplex state.
scalar:Uint32 operEEERxWkTime  (ethpm:If:operEEERxWkTime)
           Operational port EEE rx time
l1:EEEState
          scalar:Enum8 		operEEEState  (ethpm:If:operEEEState)
           Operational port EEE state
scalar:Uint32 operEEETxWkTime  (ethpm:If:operEEETxWkTime)
           Operational port EEE tx time
l1:OperErrDisQual
          scalar:Enum32 		operErrDisQual  (ethpm:If:operErrDisQual)
           The operational port error disable reason code.
l1:FlowCtrlVal
          scalar:UByte 		operFlowCtrl  (ethpm:If:operFlowCtrl)
           Operational port flow control
l1:Mdix
          scalar:Enum8 		operMdix  (ethpm:If:operMdix)
           port oper mdix mode
l1:Mode
          scalar:Enum8 		operMode  (ethpm:If:operMode)
           The operational port mode.
l1:OperSt
          scalar:Enum8 		operPhyEnSt  (ethpm:If:operPhyEnSt)
           Operational phy port enable state
address:MAC operRouterMac  (ethpm:If:operRouterMac)
           Operational port router mac
l1:Speed
          scalar:Enum8 		operSpeed  (ethpm:If:operSpeed)
           Operational port speed
l1:OperSt
          scalar:Enum8 		operSt  (ethpm:If:operSt)
           The operational port state.
l1:OperStQual
          scalar:Enum32 		operStQual  (ethpm:If:operStQual)
           The operational state failure reason.
l1:OperStQualCode
          scalar:Uint32 		operStQualCode  (ethpm:If:operStQualCode)
           Operational port status syserror code
l2:VlanBitmap
          base:BitArray4096 		operVlans  (ethpm:If:operVlans)
           operational vlans
nw:OSSum
          scalar:Enum8 		osSum  (ethpm:If:osSum)
           Operational state summary
scalar:Uint32 portCfgWaitFlags  (ethpm:If:portCfgWaitFlags)
           port config wait flags
base:Encap primaryVlan  (ethpm:If:primaryVlan)
           port primary-vlan
scalar:Uint32 resetCtr  (ethpm:If:resetCtr)
           reset counter
ethpm:SiBitmap
          base:BitArray4096 		siList  (ethpm:If:siList)
           configured sub-interface ids
l1:TxT
          scalar:Enum8 		txT  (ethpm:If:txT)
           port Tx type
l1:PortUsage
          scalar:Bitmask32 		usage  (ethpm:If:usage)
          
scalar:Uint32 userCfgdFlags  (ethpm:If:userCfgdFlags)
           port user config flags
l2:VdcId
          scalar:Uint16 		vdcId  (ethpm:If:vdcId)
           vdc id
Defined in: mo:TopProps
mo:ModificationChildAction
          scalar:Bitmask32 		childAction  (mo:TopProps:childAction)
           Delete or ignore. For internal use only.
reference:BinRef dn  (mo:TopProps:dn)
           A tag or metadata is a non-hierarchical keyword or term assigned to the fabric module.
reference:BinRN rn  (mo:TopProps:rn)
           Identifies an object from its siblings within the context of its parent object. The distinguished name contains a sequence of relative names.
mo:ModificationStatus
          scalar:Bitmask32 		status  (mo:TopProps:status)
           The upgrade status. This property is for internal use only.
Properties Detail

accessVlan

Type: base:Encap

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The VLAN port access state.


allowedVlans

Type: l2:VlanBitmap
Primitive Type: base:BitArray4096

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
allowed vlans


backplaneMac

Type: address:MAC

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port backplane mac


bundleBupId

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
bundle bringup id


bundleIndex

Type: nw:IfId
Primitive Type: base:IfIndex

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The interface bundle index. A bundle index is a table for a particular output primitive. It defines the workstation dependent aspects of the primitive.


cfgAccessVlan

Type: base:Encap

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The port configuration access VLAN.


cfgNativeVlan

Type: base:Encap

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The port configuration native VLAN.


childAction

Type: mo:ModificationChildAction
Primitive Type: scalar:Bitmask32

Units: null
Encrypted: false
Access: implicit
Category: TopLevelChildAction
    Comments:
Delete or ignore. For internal use only.
Constants
deleteAll 16384u deleteAll NO COMMENTS
ignore 4096u ignore NO COMMENTS
deleteNonPresent 8192u deleteNonPresent NO COMMENTS
DEFAULT 0 --- This type is used to




currErrIndex

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
current error index


diags

Type: l1:DiagsT
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port diags type
Constants
none 1 none NO COMMENTS
dom 2 dom NO COMMENTS
ddm 3 ddm NO COMMENTS
DEFAULT none(1) none NO COMMENTS




dn

Type: reference:BinRef

Units: null
Encrypted: false
Access: implicit
Category: TopLevelDn
    Comments:
A tag or metadata is a non-hierarchical keyword or term assigned to the fabric module.


encap

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port encap


errDisTimerRunning

Type: scalar:Bool

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
error disable recovery time running
Constants
no false --- NO COMMENTS
yes true --- NO COMMENTS
DEFAULT no(false) --- NO COMMENTS




errVlanStatusHt

Type: ethpm:ErrorVlanStatusList
Primitive Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port per vlan error state


errVlans

Type: l2:VlanBitmap
Primitive Type: base:BitArray4096

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
errored vlans


hwBdId

Type: l2:DomId
Primitive Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
hw bd id (allocated for l3 ports, port-channels)


hwResourceId

Type: l2:HwRsrcIdT
Primitive Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Hardware resource identifier (allocated by eltm)


intfT

Type: l1:IntfT
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
interface type
Constants
phy 1 phy NO COMMENTS
phy-shared 2 phy-shared NO COMMENTS
DEFAULT phy(1) phy NO COMMENTS




iod

Type: scalar:Uint64

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
iod


lastErrors

Type: ethpm:LastErrorsList
Primitive Type: base:Uint32Array4

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
last seen errors


lastLinkStChg

Type: scalar:Date

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Last link state change


media

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port media


nativeVlan

Type: base:Encap

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port native vlan


numOfSI

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
number of sub-interfaces


operBitset

Type: ethpm:PortOperBitmap
Primitive Type: base:BitArray64

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port oper bitset


operDceMode

Type: l1:DceMode
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational Dce Mode
Constants
core 1 core NO COMMENTS
edge 2 edge NO COMMENTS
auto 3 auto NO COMMENTS
off 4 off NO COMMENTS
DEFAULT off(4) off NO COMMENTS




operDuplex

Type: l1:Duplex
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The operational duplex state.
Constants
auto 1 auto NO COMMENTS
full 2 full NO COMMENTS
half 3 half NO COMMENTS
DEFAULT auto(1) auto NO COMMENTS




operEEERxWkTime

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational port EEE rx time


operEEEState

Type: l1:EEEState
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational port EEE state
Constants
enable 1 enable NO COMMENTS
disable 2 disable NO COMMENTS
disagreed 3 disagreed NO COMMENTS
not-applicable 4 not-applicable NO COMMENTS
DEFAULT not-applicable(4) not-applicable NO COMMENTS




operEEETxWkTime

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational port EEE tx time


operErrDisQual

Type: l1:OperErrDisQual
Primitive Type: scalar:Enum32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The operational port error disable reason code.
Constants
unknown 0u down The port state is unknown
sfp-missing 10u sfpAbsent The SFP is absent on this port
loopback-diag-failure 11u faulty NO COMMENTS
udld-unidir-detected 12u udldUnidir NO COMMENTS
udld-tx-rx-loop 13u udldLoop NO COMMENTS
udld-neighbor-mismatch 14u udldMismatch NO COMMENTS
udld-empty-echo 15u udldEmpEcho NO COMMENTS
udld-aggressive-mode-link-failed 16u udldAggr NO COMMENTS
link-flap-err 17u linkFlapErr NO COMMENTS
err-disabled-ip-conflict 18u conflctErrDis NO COMMENTS
ipqos-dcbxp-compat-failure 19u ipQosDcbxpCompatFailure NO COMMENTS
up 1u up This port is operationally up
link-failure 20u notconnect NO COMMENTS
offline 21u offline NO COMMENTS
initializing 22u init NO COMMENTS
inactive 23u inactive NO COMMENTS
channel-admin-down 24u channelDown NO COMMENTS
channel-err-disabled 25u Channel error-disabled-err-disabled NO COMMENTS
suspended 26u suspnd NO COMMENTS
proto-port-suspend 27u portSuspnd NO COMMENTS
channel-membership-update-in-progress 28u channelUpdate NO COMMENTS
parent-down 29u parentDown NO COMMENTS
admin-down 2u disabled This port is down because it is admin down
parent-admin-down 30u adminDown-parentDown NO COMMENTS
interface-removed 31u ifRemoved NO COMMENTS
fcot-no-present 32u fcotAbsent NO COMMENTS
fcot-vendor-not-supported 33u SFP vendor not supported-err-disabled NO COMMENTS
incompatible-admin-mode 34u errDisabledIncompatPortMode-err-disabled NO COMMENTS
incompatible-admin-speed 35u errDisabledIncompatPortSpeed-err-disabled NO COMMENTS
suspended-by-mode 36u suspended-by-mode NO COMMENTS
suspended-by-speed 37u suspended-by-speed NO COMMENTS
domain-max-retransmission-failure 38u isolated NO COMMENTS
loopback-isolation 39u isolated NO COMMENTS
link-down 3u parentEthDown The link is down
upgrade-in-progress 40u modUpgrade NO COMMENTS
port-channel-members-down 41u noOperMembers NO COMMENTS
ethernet-link-down 42u parentEthDown NO COMMENTS
ethernet-interface-down 43u interface-parentEthDown NO COMMENTS
admin-config-change 44u adminCfgChng NO COMMENTS
module-removed 45u modRemoved NO COMMENTS
vrf-unusable 46u vrfUnusable NO COMMENTS
none 47u connected NO COMMENTS
xcvr-initializing 48u sfpInit NO COMMENTS
cap-absent 49u capAbsent NO COMMENTS
fail 4u fail The link is failed state
sfp-eth-compliant-err 50u xcvrEthComplianceErr NO COMMENTS
sdp-timeout 51u SDP timeout/SFP Mismatch NO COMMENTS
sat-incompat-topo 52u FEX identity mismatch NO COMMENTS
sat-not-configured 53u FEX not configured NO COMMENTS
auth-fail 54u xcvrAuthFailed NO COMMENTS
auth-pending 55u authPending NO COMMENTS
suspended-due-to-minlinks 56u suspendedMinLinks NO COMMENTS
suspended-due-to-no-lacp-pdus 57u suspended(no LACP PDUs) NO COMMENTS
sat-fabric-if-down 58u fabrcIfDown NO COMMENTS
invalid-sat-fabric-if 59u invalidFbIf NO COMMENTS
no-license 5u portLicNtAvl The port has no valid license
fex-sfp-invalid 60u FEX-fabric sfp invalid NO COMMENTS
suspend-by-mtu 61u mtuFailure NO COMMENTS
suspend-by-vpc 62u suspndByVpc NO COMMENTS
router-mac-failure 63u routrmacFail NO COMMENTS
xcvr-auth-failed 64u xcvrAuthFailed NO COMMENTS
non-sticky-externally-disabled 65u ServDisab NO COMMENTS
sfp-speed-mismatch 66u xcvrSpeedMismatch NO COMMENTS
fcot-chksum-err 67u SFP checksum error NO COMMENTS
xcvr-invalid 68u Transceiver validation failed NO COMMENTS
vpc-peer-link-down 69u vpcPeerLinkDown NO COMMENTS
link-up 6u link-up-connected The link is up
vpc-cfg-in-progress 70u vpcConfigInProgress NO COMMENTS
vpc-no-response-from-peer 71u noRespFrmVpc NO COMMENTS
bpdu-guard-err-disable 72u BPDUGuard errDisable NO COMMENTS
hot-standby-in-bundle 73u htStdbyInBndl NO COMMENTS
handshake-fail-errdisable 74u intFailErrDis NO COMMENTS
mcp-loop-err-disable 75u mcpLoop errDisable NO COMMENTS
epm-learn-err-disable 76u epmLearn errDisable NO COMMENTS
mac-pinning 77u macPinning NO COMMENTS
fabric-track 78u fabricTrack NO COMMENTS
configuration-incomplete 79u incomplete config NO COMMENTS
hw-fail 7u faulty This port has a hardware failure
ethernet-vlan-down 80u parentVlanDown NO COMMENTS
link-fail-reset 81u linkReset NO COMMENTS
vfc-binding-invalid 82u vfcBindingInvalid NO COMMENTS
vlan-not-fcoe-enabled 83u vlanNotFcoeEnabled NO COMMENTS
ethernet-invalid-binding 84u parentInvalidBinding NO COMMENTS
link-fail-port-unusable 85u linkFailPortUnusable NO COMMENTS
diag-failure-errdisable 86u diag failure errDisable NO COMMENTS
incompatible-fecmode 87u errDisabledIncompatFECMode-err-disabled NO COMMENTS
npm-no-ext-link 88u NPV upstream port not available NO COMMENTS
port-reinit-limit 89u Port reinit threshold reached NO COMMENTS
sw-fail 8u faulty This port has a software failure
npiv-not-enb-upstream 90u NPIV upstream port not available NO COMMENTS
vsan-mismatch-upstream 91u VSAN mismatch with upstream port NO COMMENTS
pause-rate-limit-err-disable 92u pauseRateLimit errDisable NO COMMENTS
hw-disabled 93u hwDisabled NO COMMENTS
err-disabled 9u err-disabled The port is in err disable mode
DEFAULT admin-down(2u) disabled This port is down because it is admin down




operFlowCtrl

Type: l1:FlowCtrlVal
Primitive Type: scalar:UByte

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational port flow control
Constants
defaultValue 0xf --- NO COMMENTS




operMdix

Type: l1:Mdix
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port oper mdix mode
Constants
auto 1 auto NO COMMENTS
mdi 2 mdi NO COMMENTS
mdi-x 3 mdi-x NO COMMENTS
DEFAULT auto(1) auto NO COMMENTS




operMode

Type: l1:Mode
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The operational port mode.
Constants
unknown 0 unknown NO COMMENTS
access 1 access NO COMMENTS
trunk 2 trunk NO COMMENTS
fex-fabric 3 fex-fabric NO COMMENTS
qiq-tunnel-edgePort 4 qiq-tunnel-edgePort NO COMMENTS
qiq-tunnel-corePort 5 qiq-tunnel-corePort NO COMMENTS
DEFAULT trunk(2) trunk NO COMMENTS




operPhyEnSt

Type: l1:OperSt
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational phy port enable state
Constants
unknown 0 unknown Unknown state
down 1 down Port is down
up 2 up Port is up
link-up 3 link-up Port is link-up
DEFAULT down(1) down Port is down




operRouterMac

Type: address:MAC

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational port router mac


operSpeed

Type: l1:Speed
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational port speed
Constants
unknown 0 Unspecified Speed is unknown
100M 1 100 Mbps Speed is 100 Mbps
1G 2 1 Gbps Speed is 1 Gbps
10G 3 10 Gbps Speed is 10 Gbps
25G 4 25 Gbps Speed is 25 Gbps
40G 5 40 Gbps Speed is 40 Gbps
100G 6 100 Gbps Speed is 100 Gbps
inherit 7 inherit Speed is Inherited
DEFAULT inherit(7) inherit Speed is Inherited




operSt

Type: l1:OperSt
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The operational port state.
Constants
unknown 0 unknown Unknown state
down 1 down Port is down
up 2 up Port is up
link-up 3 link-up Port is link-up
DEFAULT down(1) down Port is down




operStQual

Type: l1:OperStQual
Primitive Type: scalar:Enum32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
The operational state failure reason.
Constants
unknown 0u down The port state is unknown
sfp-missing 10u sfpAbsent The SFP is absent on this port
loopback-diag-failure 11u faulty NO COMMENTS
udld-unidir-detected 12u udldUnidir NO COMMENTS
udld-tx-rx-loop 13u udldLoop NO COMMENTS
udld-neighbor-mismatch 14u udldMismatch NO COMMENTS
udld-empty-echo 15u udldEmpEcho NO COMMENTS
udld-aggressive-mode-link-failed 16u udldAggr NO COMMENTS
link-flap-err 17u linkFlapErr NO COMMENTS
err-disabled-ip-conflict 18u conflctErrDis NO COMMENTS
ipqos-dcbxp-compat-failure 19u ipQosDcbxpCompatFailure NO COMMENTS
up 1u up This port is operationally up
link-failure 20u notconnect NO COMMENTS
offline 21u offline NO COMMENTS
initializing 22u init NO COMMENTS
inactive 23u inactive NO COMMENTS
channel-admin-down 24u channelDown NO COMMENTS
channel-err-disabled 25u Channel error-disabled-err-disabled NO COMMENTS
suspended 26u suspnd NO COMMENTS
proto-port-suspend 27u portSuspnd NO COMMENTS
channel-membership-update-in-progress 28u channelUpdate NO COMMENTS
parent-down 29u parentDown NO COMMENTS
admin-down 2u disabled This port is down because it is admin down
parent-admin-down 30u adminDown-parentDown NO COMMENTS
interface-removed 31u ifRemoved NO COMMENTS
fcot-no-present 32u fcotAbsent NO COMMENTS
fcot-vendor-not-supported 33u SFP vendor not supported-err-disabled NO COMMENTS
incompatible-admin-mode 34u errDisabledIncompatPortMode-err-disabled NO COMMENTS
incompatible-admin-speed 35u errDisabledIncompatPortSpeed-err-disabled NO COMMENTS
suspended-by-mode 36u suspended-by-mode NO COMMENTS
suspended-by-speed 37u suspended-by-speed NO COMMENTS
domain-max-retransmission-failure 38u isolated NO COMMENTS
loopback-isolation 39u isolated NO COMMENTS
link-down 3u parentEthDown The link is down
upgrade-in-progress 40u modUpgrade NO COMMENTS
port-channel-members-down 41u noOperMembers NO COMMENTS
ethernet-link-down 42u parentEthDown NO COMMENTS
ethernet-interface-down 43u interface-parentEthDown NO COMMENTS
admin-config-change 44u adminCfgChng NO COMMENTS
module-removed 45u modRemoved NO COMMENTS
vrf-unusable 46u vrfUnusable NO COMMENTS
none 47u connected NO COMMENTS
xcvr-initializing 48u sfpInit NO COMMENTS
cap-absent 49u capAbsent NO COMMENTS
fail 4u fail The link is failed state
sfp-eth-compliant-err 50u xcvrEthComplianceErr NO COMMENTS
sdp-timeout 51u SDP timeout/SFP Mismatch NO COMMENTS
sat-incompat-topo 52u FEX identity mismatch NO COMMENTS
sat-not-configured 53u FEX not configured NO COMMENTS
auth-fail 54u xcvrAuthFailed NO COMMENTS
auth-pending 55u authPending NO COMMENTS
suspended-due-to-minlinks 56u suspendedMinLinks NO COMMENTS
suspended-due-to-no-lacp-pdus 57u suspended(no LACP PDUs) NO COMMENTS
sat-fabric-if-down 58u fabrcIfDown NO COMMENTS
invalid-sat-fabric-if 59u invalidFbIf NO COMMENTS
no-license 5u portLicNtAvl The port has no valid license
fex-sfp-invalid 60u FEX-fabric sfp invalid NO COMMENTS
suspend-by-mtu 61u mtuFailure NO COMMENTS
suspend-by-vpc 62u suspndByVpc NO COMMENTS
router-mac-failure 63u routrmacFail NO COMMENTS
xcvr-auth-failed 64u xcvrAuthFailed NO COMMENTS
non-sticky-externally-disabled 65u ServDisab NO COMMENTS
sfp-speed-mismatch 66u xcvrSpeedMismatch NO COMMENTS
fcot-chksum-err 67u SFP checksum error NO COMMENTS
xcvr-invalid 68u Transceiver validation failed NO COMMENTS
vpc-peer-link-down 69u vpcPeerLinkDown NO COMMENTS
link-up 6u link-up-connected The link is up
vpc-cfg-in-progress 70u vpcConfigInProgress NO COMMENTS
vpc-no-response-from-peer 71u noRespFrmVpc NO COMMENTS
bpdu-guard-err-disable 72u BPDUGuard errDisable NO COMMENTS
hot-standby-in-bundle 73u htStdbyInBndl NO COMMENTS
handshake-fail-errdisable 74u intFailErrDis NO COMMENTS
mcp-loop-err-disable 75u mcpLoop errDisable NO COMMENTS
epm-learn-err-disable 76u epmLearn errDisable NO COMMENTS
mac-pinning 77u macPinning NO COMMENTS
fabric-track 78u fabricTrack NO COMMENTS
configuration-incomplete 79u incomplete config NO COMMENTS
hw-fail 7u faulty This port has a hardware failure
ethernet-vlan-down 80u parentVlanDown NO COMMENTS
link-fail-reset 81u linkReset NO COMMENTS
vfc-binding-invalid 82u vfcBindingInvalid NO COMMENTS
vlan-not-fcoe-enabled 83u vlanNotFcoeEnabled NO COMMENTS
ethernet-invalid-binding 84u parentInvalidBinding NO COMMENTS
link-fail-port-unusable 85u linkFailPortUnusable NO COMMENTS
diag-failure-errdisable 86u diag failure errDisable NO COMMENTS
incompatible-fecmode 87u errDisabledIncompatFECMode-err-disabled NO COMMENTS
npm-no-ext-link 88u NPV upstream port not available NO COMMENTS
port-reinit-limit 89u Port reinit threshold reached NO COMMENTS
sw-fail 8u faulty This port has a software failure
npiv-not-enb-upstream 90u NPIV upstream port not available NO COMMENTS
vsan-mismatch-upstream 91u VSAN mismatch with upstream port NO COMMENTS
pause-rate-limit-err-disable 92u pauseRateLimit errDisable NO COMMENTS
hw-disabled 93u hwDisabled NO COMMENTS
err-disabled 9u err-disabled The port is in err disable mode
DEFAULT admin-down(2u) disabled This port is down because it is admin down




operStQualCode

Type: l1:OperStQualCode
Primitive Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational port status syserror code


operVlans

Type: l2:VlanBitmap
Primitive Type: base:BitArray4096

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
operational vlans


osSum

Type: nw:OSSum
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Operational state summary
Constants
failed 0 Failed Failed
initializing 1 Initializing Initializing
resetting 2 Resetting Resetting
degraded 3 Degraded Degraded
ok 4 Ok Ok
DEFAULT ok(4) Ok Ok




portCfgWaitFlags

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port config wait flags


primaryVlan

Type: base:Encap

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port primary-vlan


resetCtr

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
reset counter


rn

Type: reference:BinRN

Units: null
Encrypted: false
Access: implicit
Category: TopLevelRn
    Comments:
Identifies an object from its siblings within the context of its parent object. The distinguished name contains a sequence of relative names.


siList

Type: ethpm:SiBitmap
Primitive Type: base:BitArray4096

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
configured sub-interface ids


status

Type: mo:ModificationStatus
Primitive Type: scalar:Bitmask32

Units: null
Encrypted: false
Access: implicit
Category: TopLevelStatus
    Comments:
The upgrade status. This property is for internal use only.
Constants
created 2u created In a setter method: specifies that an object should be created. An error is returned if the object already exists.
In the return value of a setter method: indicates that an object has been created.
modified 4u modified In a setter method: specifies that an object should be modified
In the return value of a setter method: indicates that an object has been modified.
deleted 8u deleted In a setter method: specifies that an object should be deleted.
In the return value of a setter method: indicates that an object has been deleted.
DEFAULT 0 --- This type controls the life cycle of objects passed in the XML API.

When used in a setter method (such as configConfMo), the ModificationStatus specifies whether an object should be created, modified, deleted or removed.
In the return value of a setter method, the ModificationStatus indicates the actual operation that was performed. For example, the ModificationStatus is set to "created" if the object was created. The ModificationStatus is not set if the object was neither created, modified, deleted or removed.

When invoking a setter method, the ModificationStatus is optional:
If a setter method such as configConfMo is invoked and the ModificationStatus is not set, the system automatically determines if the object should be created or modified.





txT

Type: l1:TxT
Primitive Type: scalar:Enum8

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port Tx type
Constants
unknown 1 unknown NO COMMENTS
LL 2 LL NO COMMENTS
SN 3 SN NO COMMENTS
LC 4 LC NO COMMENTS
EL 5 EL NO COMMENTS
10GBASE-SR 6 10GBASE-SR NO COMMENTS
10GBASE-LR 7 10GBASE-LR NO COMMENTS
10GBASE-ER 8 10GBASE-ER NO COMMENTS
10GBASE-LX4 9 10GBASE-LX4 NO COMMENTS
10GBASE-SW 10 10GBASE-SW NO COMMENTS
10GBASE-LW 11 10GBASE-LW NO COMMENTS
10GBASE-EW 12 10GBASE-EW NO COMMENTS
DEFAULT unknown(1) unknown NO COMMENTS




usage

Type: l1:PortUsage
Primitive Type: scalar:Bitmask32

Like: l1:EthIf:usage
Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
Constants
out-of-service 128u Out Of Service NO COMMENTS
controller 16u Controller NO COMMENTS
discovery 1u Discovery NO COMMENTS
fabric-ext 256u Fabric External NO COMMENTS
epg 2u EPG NO COMMENTS
blacklist 32u Black listed NO COMMENTS
fabric 4u Fabric NO COMMENTS
span 64u Span NO COMMENTS
infra 8u Infra NO COMMENTS
DEFAULT discovery(1u) Discovery NO COMMENTS




userCfgdFlags

Type: scalar:Uint32

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
port user config flags


vdcId

Type: l2:VdcId
Primitive Type: scalar:Uint16

Units: null
Encrypted: false
Access: oper
Category: TopLevelRegular
    Comments:
vdc id




Overview  Diagram  Inheritance  Events  Faults  FSMs  Properties Summary  Properties Detail