June 2026

June 30 - Genie v26.6

New Module Versions

Modules	Version
genie	v26.6
genie.lamp	v26.6
genie.libs.health	v26.6
genie.libs.clean	v26.6
genie.libs.conf	v26.6
genie.libs.filetransferutils	v26.6
genie.libs.ops	v26.6
genie.libs.parser	v26.6
genie.libs.robot	v26.6
genie.libs.sdk	v26.6
genie.telemetry	v26.6
genie.trafficgen	v26.6

Changelogs

genie

Fix

• genie.conf.base.api

  • Modified CleanAPI.render_clean_template

    • Preserve clean stage configuration even when the stage is not listed in the template’s default order

genie.lamp

genie.libs.clean

Fix

• iosxe

  • Modified test_configure_replace_pass_rollback_complete

    • Added command show version | include operating mode to check for controller mode devices.

  • Modified InstallRemoveSmu clean stage

    • Re-applied connection initialization commands after SMU reload to

  • Modified image_handler

    • Use the copy_to_linux destination when copy_to_device receives an overridden image.

  • Modified InstallImage clean stage

    • Added save running-config after unconfiguring system ignore startup

    • Read debug config from active ROMMON variables.

New

• iosxe

  • Added ConfigureNetconfYang stage

    • Configure NETCONF-YANG options and verify process readiness.

  • Added VerifyNetconfProcesses stage

    • Validate NETCONF process state and datastore synchronization.

• iosxe/nxos/iosxr

  • Added roomon boot for the power cycle stage

    • Use the golden image to boot device after power cycle

genie.libs.conf

genie.libs.filetransferutils

Fix

• iosxr

  • update the sned_to_cli to just return the output, since the parent check for the failure

• filetransferutils

  • Modified HTTPS protocol support

    • Added a concrete HTTPS FileUtils protocol module so remote filesize

genie.libs.health

genie.libs.ops

New

• iosxe

  • Modified Platform

    • Added a normalized, OS-agnostic members collection to the

Fix

• base

  • Modified Platform schema

    • Added members as a top-level Any() entry so OS-specific Platform

genie.libs.robot

genie.libs.sdk

New

• iosxe

  • Added SDK API support for

    • subscriber service session-accounting

    • no subscriber service session-accounting

    • subscriber service target-atm-vc

    • no subscriber service target-atm-vc

  • Added unit test coverage for the new helper APIs.

  • Added hw_module_session to iosxe-utils.py

    • New API support for ‘hw_module_session {subslot}’ cli

  • Added get_lldp_info

    • added api to get parsed output of ‘show lldp’

  • Added get_lldp_interface_info

    • added api to get parsed output of ‘show lldp interface’

  • Added get_lldp_interface_list

    • added api to get the list of interfaces with lldp enabled

  • Added get_lldp_neighbors_brief_info

    • added api to get parsed output of ‘show lldp neighbors’

  • Added get_lldp_neighbors_interface_info

    • added api to get parsed output of

  • Added get_lldp_entry_info

    • added api to get parsed output of ‘show lldp entry’

  • Added get_total_lldp_entries_displayed

    • added api to get total lldp entries displayed

  • Added get_lldp_traffic_info

    • added api to get parsed output of ‘show lldp traffic’

  • Added get_lldp_error_info

    • added api to get parsed output of ‘show lldp errors’

  • Added

    • configure_interface_macsec_dot1q API

  • Added

    • execute_change_directory API

  • cat9kv

    • Added send_break_boot API

  • Added

    • unconfigure_interface_macsec API

  • Added get_span_session_info

    • added api to get parsed output of ‘show monitor session <session_id>’

  • Added get_span_session_running_config

    • added api to extract span session info from device running-config

  • Added collect_install_log API to collect install failure logs for c9800 device

  • Added SDK API support for

    • clear vpdn history failure

  • Added unit test coverage for the new helper API.

  • Added unconfigure_lldp_interface_only

    • added api to unconfigure lldp transmit/receive on a specific interface

  • Added configure_l2tp_class

    • added api to configure l2tp-class

  • Added unconfigure_l2tp_class

    • added api to unconfigure l2tp-class

  • Added remove_l2tp_class

    • added api to remove l2tp-class

  • Added SDK API support for

    • simulator radius request 1 coa

    • simulator radius request 1 coa

  • Added unit test coverage for the new simulator radius CoA request API.

  • Added

    • configure_plim_qos_in_map_ipv_tc_queue_strict_priority API

  • Added configure_aaa_authentication_ppp_default_type

    • added api to configure aaa authentication ppp default type

  • Added secure APIs

    • configure_username_secure

    • configure_enable_policy_password_secure

    • unconfigure_enable_policy_password_secure

    • configure_dot1x_cred_profile_secure

    • configure_credentials

    • configure_crypto

    • copy_startup_config_to_scp

    • copy_running_config_to_scp

    • configure_radius_server_secure

  • Added configure_local_span_source_and_get_output

    • added api to configure local span source interface and

  • Added configure_local_span_destination_and_get_output

    • added api to configure local span destination interface and

  • Added

    • configure_hw_module_slot_stop API

  • Added IOSXE SDK API support for

    • clear_subscriber_session_all

  • Added unit test coverage for the new API.

  • Added

    • execute_print_working_directory API

  • Added configure_virtual_ppp

    • added api to configure Virtual-PPP

  • Added unconfigure_virtual_ppp

    • added api to unconfigure Virtual-PPP

  • Added

    • clear_crypto_cryptotype API

  • Added generic IOSXE AAA SDK APIs

    • configure_aaa_authentication

    • unconfigure_aaa_authentication

    • configure_aaa_authorization

    • unconfigure_aaa_authorization

    • configure_aaa_accounting

    • unconfigure_aaa_accounting

  • Added unit test coverage for all new APIs.

  • Added

    • configure_clear_macsec_interface_statistics API

  • Added SDK APIs for L2 QoS configuration

    • configure_wrr_queue_bandwidth

    • unconfigure_wrr_queue_bandwidth

    • configure_wrr_queue_cos_map

    • unconfigure_wrr_queue_cos_map

    • configure_interface_switchport_priority_default

    • unconfigure_interface_switchport_priority_default

    • configure_interface_switchport_priority_override

    • unconfigure_interface_switchport_priority_override

    • configure_interface_switchport_priority_extend_cos

    • unconfigure_interface_switchport_priority_extend_cos

    • configure_interface_switchport_priority_extend_trust

    • unconfigure_interface_switchport_priority_extend_trust

  • Added unit test coverage for the new L2 QoS APIs.

  • Added

    • configure_interface_macsec API

  • cat9kv

    • Added configure_ignore_startup_config API.

  • Added IOSXE SDK API support for ISG control policy-map

    • configure_policy_map_type_control_isg

    • unconfigure_policy_map_type_control_isg

  • Added unit test coverage for the new APIs.

  • Added API execute_test_platform_software_command

  • Added API configure_power_redundancy

  • Added API unconfigure_power_redundancy

  • Added API configure_service_unsupported_transceiver

  • Added API unconfigure_service_unsupported_transceiver

  • Added

    • execute_fsck API

  • Added verify_show_lldp

    • added api to verify ‘show lldp’ output against expected values

  • Added verify_show_lldp_interface

    • added api to verify ‘show lldp interface’ output against

  • Added verify_show_lldp_traffic

    • added api to verify ‘show lldp traffic’ counters within min/max range

  • Added verify_show_lldp_error

    • added api to verify ‘show lldp error’ output safety

  • Added verify_lldp_entry

    • added helper api to verify a single lldp neighbor entry

  • Added verify_show_lldp_neighbors_detail

    • added api to verify ‘show lldp neighbors detail’ output

  • Added verify_show_lldp_entry

    • added api to verify ‘show lldp entry’ output against expected values

  • Added configure_interface_service_policy_type_control

    • New API for service-policy type control <policy_name> under an interface.

  • Added unconfigure_interface_service_policy_type_control

    • New API for no service-policy type control [policy_name] under an interface. policy_name is optional.

  • Added unconfigure_interface_ip_subscriber_initiator_type

    • New API for no initiator <type> under ip subscriber on an interface (e.g. dhcp, radius-proxy).

  • Enhanced configure_interface_ip_subscriber

    • Added support for initiator keyword to emit initiator <type> / initiator unclassified ... sub-commands under ip subscriber.

  • Added configure_pseudowire_class

    • added api to configure pseudowire class

  • Added unconfigure_pseudowire_class

    • added api to unconfigure pseudowire class

  • Added IOSXE SDK API support for

    • configure_policy_map_type_service_isg

    • unconfigure_policy_map_type_service_isg

    • configure_policy_map_type_control

    • unconfigure_policy_map_type_control

  • Added unit test coverage for the new APIs.

  • Added

    • configure_mpls_ldp_advertise

    • unconfigure_mpls_ldp_advertise

    • configure_vpdn_multihop

    • unconfigure_vpdn_multihop

• ios

  • Added IOS SDK API support for

    • configure_logging

    • unconfigure_logging

    • clear_logging

  • Supports optional timestamp, queue-limit, rate-limit, buffer level

  • Added unit test coverage for the new APIs.

  • Added IOS SDK API support for

    • execute_ping

  • Added unit test coverage for the new API.

  • Added IOS SDK API support for

    • configure_interface_ip_dhcp_client

      • Emits ip dhcp client <option> <type> [tag] under an interface (mirrors the iosxe API signature; supports e.g. ip dhcp client broadcast-flag clear).

    • unconfigure_interface_ip_dhcp_client

      • Emits no ip dhcp client <option> <type> [tag] under an interface (mirrors the iosxe API signature; supports e.g. no ip dhcp client broadcast-flag clear).

  • Added unit test coverage for the new APIs.

  • Added IOS SDK API support for

    • configure_static_arp

      • Emits arp <ip_address> <mac_address> ARPA globally.

    • unconfigure_static_arp

      • Emits no arp <ip_address> <mac_address> ARPA globally.

  • Added unit test coverage for the new APIs.

  • Added IOS SDK API support for

    • create_dhcp_pool - creates ip dhcp pool with the

    • modify_dhcp_pool - adds or removes optional sub-commands

    • remove_dhcp_pool - removes the DHCP pool.

  • Added unit test coverage for the new APIs.

• added get powercycler config api to return the powercycler configuration for a given target.

• blitz

  • Added

    • Added execute extract support for parserless regex extraction with typed scalar and list values, optional defaults, count bounds, deduplication, sorting, and Blitz variable saving.

    • Added unit test coverage for execute extract success, failure, scope integration, include/exclude ordering, retry, and backward-compatible save handling.

Fix

• updated api unit tests

  • IOSXE

    • Updated unittests to new testing method

      • configure_policy_map_with_no_set_dscp

      • configure_policy_map_with_percent

      • configure_policy_map_with_police_cir_percentage

      • configure_policy_map_with_pps

      • configure_service_policy_with_queueing_name

      • configure_shape_map

      • configure_table_map_on_device

      • configure_table_map_values

      • unconfigure_bandwidth_remaining_policy_map

      • unconfigure_policy_map

  • IOSXE

    • Updated unittests to new testing method

      • unconfigure_prp_sup_vlan_aware

      • unconfigure_prp_sup_vlan_aware_allowed_vlan_list

      • unconfigure_prp_sup_vlan_aware_reject_untagged

      • unconfigure_prp_sup_vlan_id

      • unconfigure_prp_sup_vlan_tagged

      • configure_no_ptp_enable_on_interface

      • configure_ptp_8275_holdover_spec_duration

      • configure_ptp_announce_transmit

      • configure_ptp_enable_on_interface

      • configure_ptp_modes

  • IOSXE

    • Updated unittests to new testing method

      • unconfigure_policy_map_class

      • unconfigure_policy_map_class_parameters

      • unconfigure_policy_map_set_cos_cos_table

      • unconfigure_policy_map_shape_on_device

      • unconfigure_policy_map_type_service

      • unconfigure_policy_map_with_pps

      • unconfigure_policy_map_with_type_queue

      • unconfigure_service_policy_with_queueing_name

      • unconfigure_table_map_values

      • configure_ip_prefix_list_deny_permit

  • IOSXE

    • Updated unittests to new testing method

      • configure_policy_map

      • configure_policy_map_class

      • configure_policy_map_class_parameters

      • configure_policy_map_class_precedence

      • configure_policy_map_on_device

      • configure_policy_map_parameters

      • configure_policy_map_set_cos_cos_table

      • configure_policy_map_type_service

      • configure_policy_map_with_dscp_police

      • configure_policy_map_with_dscp_table

  • IOSXE

    • Updated unittests to new testing method

      • unconfigure_platform_mgmt_interface

      • unconfigure_platform_qos_port_channel_aggregate

      • unconfigure_policy_map_control_service_temp

      • unconfigure_process_cpu_statistics_limit_entry_percentage_size

      • unconfigure_process_cpu_threshold_type_rising_interval

      • unconfigure_qfp_drop_threshold

      • unconfigure_rep_admin_vlan

      • unconfigure_router_bgp

      • unconfigure_router_ospf

      • unconfigure_service_compress_config

  • IOSXE

    • Updated unittests to new testing method

      • configure_license_smart_proxy

      • configure_license_smart_transport_callhome

      • configure_license_smart_transport_cslu

      • configure_license_smart_url

      • configure_license_smart_url_cslu

      • configure_license_smart_usage_interval

      • configure_line_console

      • configure_platform

      • configure_smart_transport_url

      • unconfigure_call_home

  • IOSXE

    • Updated unittests to new testing method

      • config_policy_map_on_interface

      • config_qos_rewrite_dscp

      • config_replace_to_flash_memory

      • config_replace_to_flash_memory_force

      • configure_auto_qos

      • configure_auto_qos_global

      • configure_ip_access_list_with_dscp_on_device

      • configure_queue_sub_interface

      • copy_running_config_to_flash_memory

      • unconfig_qos_rewrite_dscp

  • IOSXE

    • Updated unittests to new testing method

      • unconfigure_auto_qos

      • unconfigure_auto_qos_global

      • unconfigure_policy_map_on_interface

      • config_standby_console_enable

      • configure_redundancy

      • unconfigure_redundancy

      • configure_fast_rep_segment

      • configure_rep_segment

      • unconfigure_fast_rep_segment

      • unconfigure_rep_segment

  • IOSXE

    • Updated unittests to new testing method

      • unconfigure_license_smart_url_cslu

      • unconfigure_license_smart_usage_interval

      • unconfigure_smart_transport_url

      • configure_class_map

      • configure_class_map_access_group_on_device

      • configure_traffic_class_for_class_map

      • unconfigure_class_map

      • config_policy_map_on_device

      • configure_bandwidth_remaining_policy_map

      • configure_hqos_policer_map

  • IOSXE

    • Updated unittests to new testing method

      • unconfigure_http_client_secure_trustpoint

      • unconfigure_http_client_source_interface

      • unconfigure_http_secure_trustpoint

      • unconfigure_ip_domain_name

      • unconfigure_ip_domain_timeout

      • unconfigure_ip_http_authentication_local

      • unconfigure_ip_http_secure_server

      • unconfigure_ip_http_server

      • unconfigure_license_smart_proxy

      • unconfigure_license_smart_transport

  • IOSXE

    • Updated unittests to new testing method

      • configure_ip_prefix_list_description

      • configure_ip_prefix_list_seq

      • configure_prp_static_vdan_entry

      • configure_prp_static_vdan_entry_with_vlan

      • configure_prp_sup_vlan_aware

      • configure_prp_sup_vlan_aware_allowed_vlan_list

      • configure_prp_sup_vlan_aware_reject_untagged

      • configure_prp_sup_vlan_id

      • configure_prp_sup_vlan_tagged

      • unconfigure_prp_static_vdan_entry

  • IOSXE

    • Updated unittests to new testing method

      • unconfigure_virtual_service

      • unconfigure_virtual_service_activate

      • configure_call_home

      • configure_exec_prompt_timestamp

      • configure_http_client_secure_trustpoint

      • configure_http_secure_trustpoint

      • configure_ip_domain_timeout

      • configure_ip_http_authentication_local

      • configure_ip_http_secure_server

      • configure_license_smart

  • IOSXE

    • Updated unittests to new testing method

      • configure_ptp_neighbor_propagation_delay_threshold

      • configure_ptp_priority

      • configure_ptp_role_primary

      • configure_ptp_source

      • configure_ptp_vlan

      • unconfigure_ptp_8275_holdover_spec_duration

      • unconfigure_ptp_announce_transmit

      • unconfigure_ptp_modes

      • unconfigure_ptp_neighbor_propagation_delay_threshold

      • unconfigure_ptp_vlan

  • IOSXE

    • Updated unittests to new testing method

      • unconfigure_license_smart_reservation

      • unconfigure_line_vty

      • unconfigure_macro_auto_global_processing

      • unconfigure_macro_auto_global_processing_on_interface

      • unconfigure_macro_auto_processing_on_interface

      • unconfigure_macro_auto_sticky

      • unconfigure_mdix_auto

      • unconfigure_parser_view

      • unconfigure_periodic_time_range

      • unconfigure_platform_acl_egress_dscp_enable

• iosxe

  • Modified verify_ignore_startup_config

    • Read ignore-startup-config from the active ROMMON variables.

  • Modified configure_vpdn_group

    • modified api configure_vpdn_group

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_configure_port_channel_lacp_max_bundle

    • test_api_configure_port_channel_standalone_disable

    • test_api_configure_power_efficient_ethernet_auto

    • test_api_configure_power_inline

    • test_api_configure_ppp_multilink

    • test_api_configure_pppoe_enable_interface

    • test_api_configure_print_timestamp_for_show_command

    • test_api_configure_scale_subintfs_via_tftp

    • test_api_configure_service_instance

    • test_api_configure_service_policy_type_queueing_on_interface

  • Removed mock_data.yaml files for the above tests as they are no longer

  • Updated configure_management_master_key

    • Added logic to check if master key is already configured and skip configuration if any warning message return by device.

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_configure_ipv6_mtu

    • test_api_configure_ipv6_nd_dad_processing

    • test_api_configure_ipv6_nd_suppress_ra

    • test_api_configure_ipv6_prefix_name_on_interface

    • test_api_configure_mdns_on_interface_vlan

    • test_api_configure_medium_p2p_interface

    • test_api_configure_monitor_erspan_source_interface

    • test_api_configure_phymode_ignore_linkup_fault

    • test_api_configure_physical_interface_vmi

    • test_api_configure_portchannel_dpi_algorithm

  • Removed mock_data.yaml files for the above tests as they are no longer

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_unconfig_interface_ospfv3

    • test_api_unconfig_interface_ospfv3_cost

    • test_api_unconfig_interface_ospfv3_flood_reduction

    • test_api_unconfig_interface_ospfv3_network_type

    • test_api_unconfig_interface_prpchannel

    • test_api_unconfig_ip_domain_lookup

    • test_api_unconfigure_control_policies

    • test_api_unconfigure_crypto_map_on_interface

    • test_api_unconfigure_eapol_eth_type_interface

    • test_api_unconfigure_eui_64_over_ipv6_enabled_interface

  • Removed mock_data.yaml files for the above tests as they are no longer

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_configure_span_monitor_session

    • test_api_configure_sub_interface_encapsulation_dot1q

    • test_api_configure_sub_interface_range

    • test_api_configure_subinterface

    • test_api_configure_subinterface_second_dot1q

    • test_api_configure_switchport_mode_trunk_snooping_trust

    • test_api_configure_switchport_nonegotiate

    • test_api_configure_switchport_protected

    • test_api_configure_switchport_pvlan_trunk_allowed_vlan

    • test_api_configure_switchport_pvlan_trunk_native_vlan

  • Removed mock_data.yaml files for the above tests as they are no longer

  • Modified the following unit tests to use unittest.mock.Mock instead of mock_device_cli

    • test_api_configure_interface_vlan

    • test_api_configure_ip_dlep

    • test_api_configure_ip_on_atm_interface

    • test_api_configure_ip_on_tunnel_interface

    • test_api_configure_ip_unnumbered_on_interface

    • test_api_configure_ipv4_dhcp_relay_helper_vrf

    • test_api_configure_ipv6_address_config

    • test_api_configure_ipv6_address_on_hsrp_interface

    • test_api_configure_ipv6_enable

    • test_api_configure_ipv6_mld_static_group

  • Removed mock_data.yaml files for the above tests as they are no longer needed

  • modified existing APIs to secure

    • configure_masked_unmasked_enable_secret_password

    • unconfigure_system_disable_password_recovery_switch_all

  • Modified the following unit tests to use unittest.mock.Mock instead of mock_device_cli

    • test_api_configure_interface_switchport_access_vlan

    • test_api_configure_interface_switchport_block_address

    • test_api_configure_interface_switchport_dot1q_ethertype

    • test_api_configure_interface_switchport_port_security_violation

    • test_api_configure_interface_switchport_pvlan_and_native_vlan

    • test_api_configure_interface_switchport_pvlan_association

    • test_api_configure_interface_switchport_pvlan_mapping

    • test_api_configure_interface_switchport_pvlan_mode

    • test_api_configure_interface_switchport_trunk

    • test_api_configure_interface_template_sticky

  • Removed mock_data.yaml files for the above tests as they are no longer needed

  • management

    • Updated configure_ip_ssh_version API to support integer SSH version input.

  • Modified the following unit tests to use unittest.mock.Mock instead of mock_device_cli

    • test_api_configure_interface_snmp_trap_mac_notification_change

    • test_api_configure_interface_span_cost

    • test_api_configure_interface_span_portfast

    • test_api_configure_interface_span_vlan_priority

    • test_api_configure_interface_speed

    • test_api_configure_interface_speed_auto

    • test_api_configure_interface_split_horizon_eigrp

    • test_api_configure_interface_storm_control_action

    • test_api_configure_interface_storm_control_level

    • test_api_configure_interface_switchport

  • Removed mock_data.yaml files for the above tests as they are no longer needed

  • Modified configure_replace

    • Added support for controller mode devices where ‘configure replace’ is not supported.

  • Modified configure_virtual_template

    • modified api configure_virtual_template

  • Modify iosxe port-settings API

    • API support error_pattern.

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_unconfigure_interface_access_session

    • test_api_unconfigure_interface_auth_vlan

    • test_api_unconfigure_interface_auth_vlan_no_resp

    • test_api_unconfigure_interface_authentication_violation

    • test_api_unconfigure_interface_bandwidth

    • test_api_unconfigure_interface_channel_group_auto_lacp

    • test_api_unconfigure_interface_dot1x_eap_profile

    • test_api_unconfigure_interface_dot1x_max_reauth_req

    • test_api_unconfigure_interface_dot1x_max_req

    • test_api_unconfigure_interface_dot1x_timeout_txp

  • Removed mock_data.yaml files for the above tests as they are no longer

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_configure_vrf_select_source

    • test_api_configure_vrrp_on_interface

    • test_api_configure_vrrp_version_on_device

    • test_api_disable_autostate_on_interface

    • test_api_disable_ipv6_address_dhcp

    • test_api_disable_ipv6_dhcp_server

    • test_api_disable_switchport_trunk_on_interface

    • test_api_enable_ipv6_address_dhcp

    • test_api_enable_ipv6_dhcp_server

    • test_api_enable_switchport_protected_on_interface

  • Removed mock_data.yaml files for the above tests as they are no longer

  • Added APIs for EVPN Route Leaking with allow-evpn keyword

    • configure_vrf_export_ipv4_unicast_map_allow_evpn

    • configure_vrf_import_ipv4_unicast_map_allow_evpn

    • configure_vrf_export_ipv6_unicast_map_allow_evpn

    • configure_vrf_import_ipv6_unicast_map_allow_evpn

    • unconfigure_vrf_ipv4_unicast_map_allow_evpn

    • unconfigure_vrf_ipv6_unicast_map_allow_evpn

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_unconfigure_interface_duplex_mode

    • test_api_unconfigure_interface_flow_control

    • test_api_unconfigure_interface_inherit_disable

    • test_api_unconfigure_interface_ip_nbar

    • test_api_unconfigure_interface_ip_tcp_adjust_mss

    • test_api_unconfigure_interface_ip_verify_source

    • test_api_unconfigure_interface_ip_verify_unicast

    • test_api_unconfigure_interface_ipv6_tcp_adjust_mss

    • test_api_unconfigure_interface_ipv6_verify_unicast

    • test_api_unconfigure_interface_l2protocol_tunnel

  • Removed mock_data.yaml files for the above tests as they are no longer

  • BLITZ

    • Modified gnmi_util script

      • modified prefix handling when building GNMI Json

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_unconfigure_interface_rep_segment_edge_preferred

    • test_api_unconfigure_interface_rep_stcn_segment

    • test_api_unconfigure_interface_rep_stcn_stp

    • test_api_unconfigure_interface_service_policy

    • test_api_unconfigure_interface_snmp_trap_mac_notification_change

    • test_api_unconfigure_interface_span_cost

    • test_api_unconfigure_interface_span_vlan_priority

    • test_api_unconfigure_interface_speed

    • test_api_unconfigure_interface_storm_control_action

    • test_api_unconfigure_interfaces_on_port_channel

  • Removed mock_data.yaml files for the above tests as they are no longer

  • Fixed snmp / ssh configuration APIs

    • test_api_snmp_trap_type_regression

    • configure_snmp_server_trap

    • unconfigure_snmp_server_trap

    • unconfigure_snmp_server_group

    • unconfigure_snmp_server_user

    • configure_ip_ssh_version

  • Modified the following unit tests to use unittest.mock.Mock instead of

    • test_api_configure_switchport_trunk_allowed_vlan

    • test_api_configure_switchport_trunk_native_vlan

    • test_api_configure_switchport_trunk_native_vlan_tag

    • test_api_configure_switchport_trunk_vlan

    • test_api_configure_switchport_trunk_vlan_with_speed_and_duplex

    • test_api_configure_system_debounce_link_down_timer

    • test_api_configure_system_debounce_link_up_timer

    • test_api_configure_tunnel_with_ipsec

    • test_api_configure_uplink_interface

    • test_api_configure_vfi

  • Removed mock_data.yaml files for the above tests as they are no longer

• abstracted_libs

  • Modified processors

    • Added error_pattern support to pre_execute_command and post_execute_command.

    • Suppressed device-level execute error patterns when error_pattern is an empty list.

    • Preserved the original execute failure when reconnect recovery cannot be performed.

• blitz

  • Modified actions and markup

    • Hardened debug logging so unsafe output stringification does not fail actions.

• modified execute powercycler apis

  • Parallelized independent power_cycler entries for power on and power off operations.

  • Preserved existing single powercycler behavior.

• modified get powercycler apis

  • Uses get powercycler config API to return the powercycler object for a given device.

• powercycler

  • Modified SNMPv3 powercycler authentication handling to use credentials

  • Added unit test coverage for powercycler-scoped SNMPv3 credentials,

• iosxr

  • update the md5 check to use bash for calculating the hash.

Mock_Device_Cli

Needed

genie.libs.parser

Fix

• iosxe

  • Modified ShowPortSecurityAddress

    • Modified parser regex to allow space and parenthesis in remaining_age field.

  • Modified SnmpGetBulk

    • Updated status handling to set success only after matching SNMP response, MIB, or hex value output.

    • Added empty parser test coverage for unmatched command error output.

  • Modified ShowIpv6Interface

    • Updated regex handling to compile patterns once before line

    • Updated nested output creation to use local dictionaries and

    • Updated joined group address matching so brief-style output with

  • Modified ShowIpv6InterfaceBrief

    • Added parsing for unnumbered interface references in brief output.

    • Added unittest coverage for unassigned rows, link-local and global

  • Modified ShowFlowMonitorCache

    • ‘show flow monitor {name} cache’

  • Modified ShowSdmPrefer

    • Made ‘vrf_count’ field optional in schema to support outputs that do not contain the ‘VRF’

  • Modified ShowDeviceTrackingDatabaseMacDetails

    • show device-tracking database mac details Better handling for MACs with no bound IP

  • Modified ShowBgpAllDetail

    • Updated next-hop parsing to support IPv6 next-hop lines with link-local addresses, preventing parser crashes on RFC5549 BGP output.

  • Modified ShowMacAddressTableCount

    • Made ‘total_mac_address_space’ Optional in schema to support output

  • Modified ShowMacAddressTableCountVlan

    • Made ‘Total_mac_address_space’ Optional in schema to support output

  • Modified ShowUACUplink, ShowUACUplinkDB, ShowUACActivePort, ShowUACActiveVlan

    • Added rv1 parser support for these commands.

  • Fixed show module parser

    • Relaxed ShowModule schema so blank/empty module slots in stacked

  • Modified ShowPortSecurityAddress

    • Modified ShowPortSecurityAddress parser to handle multiple MACs per interface.

  • Modified ShowOspfv3RibRedistribution

    • Added Optional source_vrf key to schema.

    • Added p_vrf regex pattern to parse source_vrf from route origin

    • Updated p1 regex pattern to support VRF headers in OSPFv3 RIB

  • Modified ShowFlowMonitorCache parser

    • Parser now correctly handles show flow monitor cache states.

  • Modified ShowPlatformSoftwareFedSwitchWdavcFlows parser

    • Added new regex to capture the new output of the command “show platform software fed switch wdavc flows”.

  • Modified ShowPlatformsoftwarefedswitchactivesecurityfedpmifid parser

    • Modified the existing regex to capture the new output of the command “show platform software fed switch active security fed pmifid”.

  • Modified ShowInventory (rv1)

    • Fixed PID-keyed clobber for multi-chassis SVL pairs (e.g.,

  • Fixed show xfsu eligibility parser

    • Updated schema and parser for xfsu eligibility parser.

• nxos

  • Modified ShowModule

    • Moved LFM modules from LC to XBAR section to avoid CTC LC collection failures

• iosxr

  • Modified ShowIpv6VrfAllInterface

    • Added regex to parse “IPv6 is down (link local duplicate)” state so the ‘enabled’ key is populated and the schema does not raise a missing key error.

  • Modified AdminShowDiagChassis

    • Changed ‘vid’ key from required to Optional in the schema so that chassis with an empty/blank “Version Identifier” field in ‘admin show diag chassis’ output no longer raise a SchemaMissingKeyError.

New

• iosxe

  • Added ShowWrrQueueBandwidth

    • Added schema and parser for ‘show wrr-queue bandwidth’

  • Added ShowWrrQueueCosMap

    • Added schema and parser for ‘show wrr-queue cos-map’

  • Added ShowIpPortbundleStatus

    • Added schema and parser for ‘show ip portbundle status’

  • Added ShowCloudMgmtConfigUpdater

    • Added new parser for ‘show cloud-mgmt config-updater’ command. This parser is the same as the one for ‘show meraki config updater’.

  • Added ShowSubscriberService

    • Added schema and parser for ‘show subscriber service’

  • Added ShowFlowRecordName

    • Added schema and parser for ‘show flow record {record_name}’

  • Added ShowLispNamedServicesServer for

    • show lisp instance-id {instance_id} named-services server

    • show lisp {lisp_id} instance-id {instance_id} named-services server

    • show lisp locator-table {locator_table} instance-id {instance_id} named-services server

  • Added ShowLispNamedServicesServerDetail for

    • show lisp instance-id {instance_id} named-services server detail

    • show lisp instance-id {instance_id} named-services server name {site_name}

    • show lisp instance-id {instance_id} named-services server {eid}

    • show lisp instance-id {instance_id} named-services server etr-address {etr_address}

    • show lisp {lisp_id} instance-id {instance_id} named-services server detail

    • show lisp {lisp_id} instance-id {instance_id} named-services server name {site_name}

    • show lisp {lisp_id} instance-id {instance_id} named-services server {eid}

    • show lisp {lisp_id} instance-id {instance_id} named-services server etr-address {etr_address}

    • show lisp locator-table {locator_table} instance-id {instance_id} named-services server detail

    • show lisp locator-table {locator_table} instance-id {instance_id} named-services server name {site_name}

    • show lisp locator-table {locator_table} instance-id {instance_id} named-services server {eid}

    • show lisp locator-table {locator_table} instance-id {instance_id} named-services server etr-address {etr_address}

  • Added ShowPlatformConditions

    • Added schema and parser for ‘show platform conditions’

  • Added ShowRedirectTranslationsIncludeIp

    • Added schema and parser for ‘show redirect translations | include <IP>’

  • Added ShowSubscriberSessionDetailed

    • Added schema and parser for ‘show subscriber session detailed’

  • Added ShowOspfv3DatabaseExternal

    • show ospfv3 database external

    • show ospfv3 vrf {vrf} database external

  • Added ShowOspfv3DatabaseNssaExternal

    • show ospfv3 database nssa-external

    • show ospfv3 vrf {vrf} database nssa-external

  • Added ShowLispNamedServicesSubscriber

    • For

      • show lisp {lisp_id} instance-id {instance_id} named-services subscriber

      • show lisp locator-table {locator_table} instance-id {instance_id} named-services subscriber

      • show lisp instance-id {instance_id} named-services subscriber

  • Added ShowLispNamedServicesPublisher

    • For

      • show lisp {lisp_id} instance-id {instance_id} named-services publisher

      • show lisp locator-table {vrf} instance-id {instance_id} named-services publisher

      • show lisp instance-id {instance_id} named-services publisher

  • Added ShowLispNamedServicesSubscription

    • For

      • show lisp {lisp_id} instance-id {instance_id} named-services subscription

      • show lisp locator-table {locator_table} instance-id {instance_id} named-services subscription

      • show lisp instance-id {instance_id} named-services subscription

  • Added ShowLispNamedServicesSubscriptionPrefix

    • For

      • show lisp instance-id {instance_id} named-services subscription {eid_prefix}

      • show lisp {lisp_id} instance-id {instance_id} named-services subscription {eid_prefix}

      • show lisp locator-table {locator_table} instance-id {instance_id} named-services subscription {eid_prefix}

      • show lisp instance-id {instance_id} named-services subscription detail

      • show lisp {lisp_id} instance-id {instance_id} named-services subscription detail

      • show lisp locator-table {locator_table} instance-id {instance_id} named-services subscription detail

  • Added ShowLispNamedServicesServerSubscription

    • For

      • show lisp {lisp_id} instance-id {instance_id} named-services server subscription

      • show lisp locator-table {locator_table} instance-id {instance_id} named-services server subscription

      • show lisp instance-id {instance_id} named-services server subscription

  • Added ShowLispNamedServicesServerSubscriptionPrefix

    • For

      • show lisp instance-id {instance_id} named-services server subscription {eid_prefix}

      • show lisp {lisp_id} instance-id {instance_id} named-services server subscription {eid_prefix}

      • show lisp locator-table {locator_table} instance-id {instance_id} named-services server subscription {eid_prefix}

      • show lisp instance-id {instance_id} named-services server subscription detail

      • show lisp {lisp_id} instance-id {instance_id} named-services server subscription detail

      • show lisp locator-table {locator_table} instance-id {instance_id} named-services server subscription detail

  • Added ShowPlatformHardwareFedSwitchForwardLastSummary

    • Added schema and parser for ‘show platform hardware fed {switch} {mode} forward last summary’

  • Added ShowVpdnTunnelAll

    • Added schema and parser for ‘show vpdn tunnel all’

  • Added ShowIpIgmpSnooping

    • Added schema and parser for ‘show ip igmp snooping’

  • Added ShowCloudMgmtConfigUpdater

    • Added new parser for ‘show cloud-mgmt config-updater’ command. This parser is the same as the one for ‘show meraki config updater’.

  • Added ShowPlatformHardwareQfpActiveFeatureL2bdDatapathSystem

    • Added schema and parser for ‘show platform hardware qfp active feature l2bd datapath system’

  • Added ShowRomvar (rv1)

    • Added role aware ROMMON variable output for HA devices.

  • Modified ShowRomvar

    • Tightened numeric ROMMON field parsing for NO_CONSOLE, BOARDID,

    • Added DEBUG_CONF key

  • Added ShowSubscriberSessionDetail

    • Added schema and parser for ‘show subscriber session detail’

  • Modified ShowOspfv3RibRedistribution

    • show ospfv3 vrf {vrf} rib redistribution

  • Added ShowOtvSummary

    • Added schema and parser for ‘show otv summary’

  • Added ShowOtvIsisNeighbors

    • Added schema and parser for ‘show otv isis neighbors’

  • Added ShowOtvRoute

    • Added schema and parser for ‘show otv route’

  • Added ShowIdmgrSessionKeyId

    • Added schema and parser for ‘show idmgr session key aaa-unique-id {aaa_unique_id}’

  • Added ShowLispMultihomingSiteId

    • show lisp multihoming site-id *

    • show lisp multihoming site-id {site_id}

  • Added ShowLispMultihomingSiteIdDetail

    • show lisp multihoming site-id * detail

    • show lisp multihoming site-id {site_id} detail

  • Added ShowVlansDot1qVlanIdGigabitethernet300Interface

    • Added schema and parser for ‘show vlans dot1q {vlan_id} gigabitethernet3/0/0 {interface}’

  • Added ShowVpdnGroupSelectSummary

    • Added schema and parser for ‘show vpdn group-select summary’

  • Added ShowSubscriberSessionAll

    • Added schema and parser for ‘show subscriber session all’

  • Added ShowPlatformSoftwareInfrastructureThreadFastpath

    • Added schema and parser for ‘show platform software infrastructure thread fastpath’

  • Added ShowVpdnSessionAll

    • show vpdn session all

  • Added ShowPolicyMapSessionOut

    • Added schema and parser for ‘show policy-map session out’

  • Added ShowPlatformSoftwareEssFpActiveL4r

    • Added schema and parser for ‘show platform software ess fp active l4r’

  • Added ShowPlatformHardwareQfpActiveInterfaceIfNameStatistics

    • Added schema and parser for ‘show platform hardware qfp active interface if-name {interface} statistics’

  • Added ShowPlatformHardwareQfpActiveInterfaceIfNamePath

    • Added schema and parser for ‘show platform hardware qfp active interface if-name {interface} path’

• nxos

  • Added ShowIpPimHostProxy

    • show ip pim host-proxy

Processing.

Modified

• iosxe

  • Updated ShowLispSiteSuperParser regexes (p2, p3_2) to accept DN-string EID prefixes (e.g. firewall, dual-stack) used by named-services output.

  • Updated ShowLispSiteDetailSuperParser regex (p3) to accept DN-string EID prefixes in EID-prefix <name> instance-id <id> lines for named-services server detail output.

  • Modified ShowLispSubscriptionSuperParser

    • Updated eid_prefix regex to accept distinguished-name style EID prefixes

  • Modified ShowLispSubscriptionPrefixSuperParser

    • Updated eid_prefix regex to accept distinguished-name style EID prefixes

  • Modified ShowLispServerSubscriptionSuperParser

    • Updated eid_prefix and registration regex to accept distinguished-name style EID prefixes

  • Modified ShowLispServerSubscriptionPrefixSuperParser

    • Updated eid_prefix regex to accept distinguished-name style EID prefixes

  • Added ShowLispNamedServicesPublication

    • show lisp instance-id {instance_id} named-services publication

    • show lisp {lisp_id} instance-id {instance_id} named-services publication

    • show lisp locator-table {vrf} instance-id {instance_id} named-services publication

  • Added ShowLispNamedServicesPublicationPrefix

    • show lisp instance-id {instance_id} named-services publication {eid_prefix}

    • show lisp {lisp_id} instance-id {instance_id} named-services publication {eid_prefix}

    • show lisp locator-table {vrf} instance-id {instance_id} named-services publication {eid_prefix}

    • show lisp locator-table vrf {vrf} instance-id {instance_id} named-services publication {eid_prefix}

Strings.

genie.telemetry